sjumbo-blog-600 mm or 24 Inches? Where Metric and Imperial Cabinet Standards Stop Matching
Home / News / Industry Updates / 600 mm or 24 Inches? Where Metric and Imperial Cabinet Standards Stop Matching

600 mm or 24 Inches? Where Metric and Imperial Cabinet Standards Stop Matching

2026-11-12

Walk to the end of a finished run and look at the fridge panel. On a metric carcass sold as a 24-inch kitchen, that panel stands about 10 mm proud of the cabinets beside it. Nobody flags it at handover. It turns up in the listing photos six months later, where it reads as two kitchens from two different suppliers.

600 mm is 23.62 inches. The box is 9.6 mm shallower than the one the drawing asked for, and the countertop follows it down: 620 mm against 635 mm.

Nobody was careless here. A frameless line runs a panel saw, an edgebander and a 32 mm drill bank, and on a metric line all three are set in millimetres. Drawings arrive in inches. Both documents are right. The box that comes off the line is the one the machine was set to.

What follows is where this actually bites — seven junctions, in the order you meet them walking in from the floor. Every one of them comes with the fix, because a list of hazards without fixes is just anxiety.

If you only remember five things

  • 600 mm is not 24 inches. An order written as “24 inch” will quietly arrive at 600.
  • The gap never shows on a single cabinet. It shows where two cabinet types meet.
  • Counter height is the expensive one: 36 in (914 mm) against 900 mm moves tiling, wall cabinets and the hood flue.
  • Accessible units fail first — 900 mm sits 36 mm above the 34 in cap used in US accessible design.
  • One sentence in the brief prevents all seven. It is at the bottom of this page.
Kitchen with tall oven housing, wall cabinets and an island built on a metric carcass
Nothing in this photograph tells you whether the boxes behind those doors are 600 mm or 24 inches. That is why the error survives all the way to handover.

Same words, two different numbers

Every collision starts with a term both sides believe they understand. “Standard base cabinet” is a real dimension in both systems. It is not the same dimension. Print this and keep it next to the drawing set.

ElementUS / imperialMetric (EU & AU)Gap
Base carcass depth24 in · 609.6 mm600 mm9.6 mm
Countertop depth25 in · 635 mm620 mm15 mm
Finished counter height36 in · 914 mm900 mm14 mm
Toe kick height4 in · 102 mm100–150 mmup to 48 mm
Toe kick setback3 in · 76 mm50–70 mmup to 26 mm
Wall cabinet depth12 in · 305 mm300–350 mm45 mm
Counter to wall cabinet18 in · 457 mm500–600 mmup to 143 mm
Tall unit height84 / 90 / 96 in2100 / 2200 / 2400 mm38 mm
Width module3 in · 76.2 mm steps100 / 150 mm stepsgrids never line up
Appliance opening30 in range, 24 in dishwasher600 mm housing, 600 mm dishwasher60–162 mm

1. The plinth sets every horizontal line above it

US detail: a 4 inch plinth with a 3 inch setback. Metric detail: 100 to 150 mm high, 50 to 70 mm setback, and Australian joinery usually lands on 150 mm. Door and drawer fronts sit on that plinth, so the plinth sets the bottom line of every door in the elevation.

Here is the trap. Take an approved US elevation — doors starting at 4 inches, a 34½ inch carcass, 36 inches finished — and build it on a 150 mm plinth. To hold the benchtop at 900 mm, the carcass has to drop to 720 mm, which is 28.35 inches instead of 34.5. The drawer stack above it has just lost 48 mm. Three drawers become two and a half, or the top one turns into a shallow box. The elevation the client signed no longer matches the joinery, and the difference is visible from the doorway.

Fix: dimension the plinth height and the door-bottom line, not just the finished counter height. Once an elevation is approved, the carcass height is a fixed number. It is not something to recalculate later to suit a metric plinth.

2. Fourteen millimetres the tiler ends up paying for

36 inches is 914 mm. Metric benches land at 900. Fourteen millimetres is under a fingernail and nobody measures it, but the finished counter height is the datum for three other things: the top of the splashback, the underside of the wall cabinets, and any window that meets the run.

Splashbacks get laid in whole tiles from the bench up, with the cut kept at the top where the wall cabinet hides it. Move the bench 14 mm and the top course becomes a sliver in the one place it cannot hide. The same shift lifts a range hood and the duct behind it, because hood clearance is measured from the cooktop, not the floor.

Fix: dimension the counter as finished height, and hand the tiler a splashback height instead of letting it fall out of the geometry on site. If a hood is in the layout, put its height on the same sheet.

3. Where the metric default fails outright: accessible units

This one is compliance, not taste. Kitchen work surfaces in US accessible design cap out at 34 inches — 864 mm — a limit that runs through both ADA detailing and Fair Housing review. A standard 900 mm bench is 36 mm over that before anyone has measured anything.

So the metric default is correct for every apartment in the building except the handful that will be inspected most closely. That is the worst kind of wrong: it only surfaces at sign-off, with the stone already cut.

Fix: split the unit schedule. Accessible and adaptable units get their own counter height and their own toe kick recess, so a wheelchair footplate clears. Do not convert one standard into the other and assume the result holds for the whole building.

Wall-hung bathroom vanity with stone top and basin
A 900 mm top is comfortable in almost every room and 36 mm too high in an accessible one. The same number is right and wrong in the same building.

4. Depth, and the 9.6 mm that waits for two cabinets to meet

A 24 inch carcass plus a 1 inch overhang gives a 25 inch counter. 600 mm plus a 20 mm top gives 620. Front edge to front edge in a photograph, both look correct. The difference only appears where one cabinet type stops and another starts:

  • A 600 mm base run dying into a 24 inch fridge panel or tall unit — a step, in the most looked-at part of the room.
  • A counter returning into a side wall, where the 9.6 mm is spent before the scribe even starts on a wall that is 8 mm out over three metres.
  • An integrated appliance set to a metric depth inside an imperial surround, so the front sits proud by exactly the difference nobody converted.

Fix: declare one carcass depth for the whole kitchen, tall units and appliance panels included. If a US appliance forces 24 inches somewhere, make it a deliberate exception on the drawing with the reason written beside it.

Built-in wardrobe with internal shelving, drawers and hanging rails
Internals are where the two systems already agree: 5 mm holes, 32 mm pitch, front row 37 mm back from the edge. Nearly every argument is on the outside.

5. Width grids that never divide into each other

US modular widths climb in 3 inch steps: 9, 12, 15, 18, 21, 24, 27, 30, 33, 36. Metric widths climb in 100 mm steps: 300, 400, 500, 600, 800, 900, 1000, 1200. Neither grid divides into the other, which causes two things.

Some sizes exist on one side only. A 450 mm drawer bank (17.7 in) has no US equivalent; a 15 inch cabinet (381 mm) has no metric one. And a run that closes perfectly on one grid leaves a remainder on the other, which becomes a filler.

3.3 metres is eleven 300 mm units, exact. In imperial it is 130 inches, which is not a multiple of three, so the run finishes with an inch of filler at one end and a scribe at the other. Neither is a crisis. Both get decided on site at four in the afternoon, which is what the 50–100 mm filler plate problem is really about.

Fix: put the filler width on the plan. A 40 mm filler beside a corner is fine. A 40 mm filler in the middle of a run at eye level is a permanent reminder of the day the grids did not line up.

6. Wall cabinets, and the 143 mm nobody re-checks

US wall cabinets are 12 inches deep, hang 18 inches above the counter and come in 30, 36 or 42 inch heights. Metric wall cabinets are 300 to 350 mm deep, hang 500 to 600 mm above the bench and come in 600 to 900 mm heights.

Eighteen inches is 457 mm. Six hundred millimetres is 600. That is a 143 mm difference in where the wall cabinets start — the single biggest un-converted number between a US drawing set and an Australian or European build. It will not fail an inspection. It puts the top line somewhere other than where the window head, the bulkhead and the hood flue were planned, and then somebody invents a detail on site to cover it.

Fix: specify the counter-to-wall-cabinet distance rather than the wall cabinet height. That distance is the number your tiler, your electrician and your range hood all depend on.

7. Tall units, ceilings, and the appliance that has to fit

US tall cabinets run 84, 90 or 96 inches — 2134, 2286, 2438 mm. Metric runs 2100, 2200 or 2400. Under a 2440 mm ceiling, a 2400 mm unit leaves 40 mm to close. A 96 inch unit leaves 1.6 mm.

Two millimetres is not a design decision, it is a tolerance argument you cannot win. Ceilings are rarely flat across four metres, so the nominal clearance is gone somewhere in the room. The 40 mm version absorbs that deviation, but only if it gets a real ceiling closure detail instead of a bead of silicone.

Appliance openings belong in the same category. A 30 inch range needs 762 mm, a 36 inch range 914 mm. Oven housings are 600 mm. Dishwashers are 610 mm in the US and 600 mm nearly everywhere else. Drop a 762 mm range opening into a 100 mm module run and the run stops closing on module — you get a 38 mm filler exactly where it is visible from the doorway.

Fix: send the appliance cutout pages, not the appliance names. Two 600 mm ovens from different brands do not share an opening height, and no factory can guess which one you meant.

Nine checks before the drawing set goes out

  1. The standard is named on page one — metric module or imperial — and nothing downstream contradicts it.
  2. Counter height is given as finished height, not carcass height.
  3. Plinth height and door-bottom line are both dimensioned.
  4. One carcass depth applies to base runs, tall units and appliance panels alike.
  5. Appliance cutout drawings are attached, with brand and model.
  6. One vertical datum, usually finished floor, and every trade is working from it.
  7. Accessible and adaptable units are scheduled separately, with their own counter height.
  8. Ceiling height is confirmed at three points along the run, not one.
  9. You know which unit the shop drawings will come back in, and who converts if it differs.

The cheapest fix in this article

One sentence, written before the quote leaves the office: this project is built to [metric module / imperial], finished counter height [900 mm / 36 in]. Everything else on this page follows from it — the plinth, the drawers, the tiling, the hood, the fillers.

We run both systems here and switch drawing templates by project rather than by production line, which is exactly why these seven junctions show up in our own reviews so often. You can see how a metric-planned job reads on an Australian-style kitchen build, or compare carcass and finish options across the kitchen cabinet range.

Questions that come up on every one of these jobs

Is a 600 mm base cabinet the same as a 24 inch base cabinet?

No. 600 mm is 23.62 inches, so the box is 9.6 mm shallower and the countertop follows it: 620 mm against 635 mm. On a single cabinet you will never see it. Where a base run meets a fridge panel or a tall unit, it becomes a visible step.

Can a metric factory build to my imperial drawing?

Yes, and it happens every week. What a factory cannot do is work out which numbers on your drawing are standard and which are exact. Send the finished counter height, the appliance cutout pages and one vertical datum, and state on page one that the imperial dimensions in the elevation are nominal.

Which of these actually costs the most when it goes wrong?

Counter height. It moves the splashback course, the wall cabinet line and the range hood flue, so one 14 mm decision reaches three trades. A depth error usually costs a filler or an end panel. A height error costs tiling and ducting.

Do 900 mm counters work in accessible units?

No. 900 mm is 35.43 inches against a 34 inch (864 mm) cap for kitchen work surfaces in US accessible design. Those units need their own detail rather than a conversion, plus their own toe kick recess so a wheelchair footplate clears.

Is the 32 mm shelf-pin system the same in both systems?

In frameless production, effectively yes: 5 mm holes on a 32 mm pitch, front row 37 mm back from the edge. It is the one part of the metric world US production already shares, which is why shelf heights almost never cause a problem on a mixed-standard project.

What is the single most common mistake?

Stacking heights from two systems. A 4 inch toe kick, a 34½ inch carcass and a 36 inch counter are three imperial numbers that hold together. Swap any one of them for its metric equivalent and the other two stop being correct — but nothing on the drawing looks wrong, which is why it reaches the saw.

How this was put together

Compiled from shop-drawing reviews and post-delivery site queries on whole-house packages for North American and Australian projects, where one factory runs two drawing templates and switches by project. Standards referenced: the ADA Standards for Accessible Design and Fair Housing design guidance for counter height and clearance, the 32 mm system as used in frameless production, and NCC wet-area and ceiling detailing for Australian work. Conversions are exact; site tolerances are not.